I chose a wonderful border print floral cotton poplin from Mood for the jacket. I have been wanting a border-print floral jacket for a while, so this was the perfect opportunity! Because the print ran lengthwise on the fabric, I knew that I wouldn't be able to follow the recommended cutting layout. Consequently, I bought a lot of extra fabric--the pattern calls for 3 yards, and I bought 5.5 yards--but it turned out to be just enough. I had lots left over due to the fabric width, but very little of the border itself.
Once I read the directions for sewing up the jacket, I realized that I had created a small issue for myself in that the jacket is made with a bias trim edging, which in this case would disrupt the lovely pattern on the fabric. Therefore, I decided to make it without the bias trim, and I am outlining my process below in case anyone else out there wants to do the same thing.
The details
After some experimentation I decided to make three quilted “pillow” pieces- the two arms and the body sewn around the edges and turned with the quilt batting inside them (like a pillow!), quilt, and then assemble the quilted pieces into the jacket and add the pockets.
Seams and cutting
The first step in making my "pillow" pieces was to add seam allowance to
the pattern pieces where bias tape was originally to go. Once I had done this, I cut out the fashion fabric, and then cut the batting pieces larger than the fashion fabric pieces- that made it easier to baste them together. I also found that pressing the batting and the fashion fabric pieces together with an iron made them stick together a little, and made the basting go more smoothly.
Sleeves
First I basted the batting to interior sleeve piece. Then, I placed the exterior sleeve piece on top of the interior piece with right sides together, and stitched the seam at
bottom of sleeve with a half-inch seam allowance. I then pressed the seam to the interior piece side, and
under stitched it so that I would have a nice clean finish. Next, I sewed the remaining seams with a quarter inch seam, leaving an
opening to turn. Then I trimmed and graded the batting
to my basting line and graded all seams, clipping where necessary. Finally, I turned the piece to the right
side, pressed, and stitched shut the opening that I used for turning.
Body
Again, first I basted the batting to the interior body pieces. Next, I sewed the interior shell together at the sides, using a half-inch seam allowance and leaving an opening in one of the seams for turning once the body had been assembled. Then I sewed the exterior shell together in the same way, but with no opening for turning, and pressed all of my seams open.
The back neck, with a half-inch seam
The armscyes, with a quarter-inch seam
The front neck, with a half-inch seam
The front opening, with a half-inch seam
The body bottom, with a half-inch seam, being careful to match up the
side seams.
Then I turned the entire piece through the opening in the interior side seam, being careful to get nice
corners (I used a point turner) and pressed the piece. Finally, I stitched the opening used for turning shut.
At this point, I marked my jacket pieces for quilting, as I thought it would be easiest to do it prior to seaming the shoulders, while the jacket could lay flat. I followed the following the pattern instructions to mark it.
Shoulders
I pinned the exterior shoulder pieces together with right sides
facing, and sewed them using a half-inch seam. They were a bit fiddly- I found it
easiest to open each shoulder up into a “tube.” After sewing, I pressed them open and trimmed the batting away
from the interior pieces at shoulder seam, and pressed that seam under by half an inch. I then basted interior shoulder seams closed, leaving me with a finished but not-yet-quilted body with no sleeves.
Quilting
At this point my pieces were all completed and ready for quilting, and I quilted per pattern instructions.
Attach arms
Once the quilting was done I attached the arms following the pattern directions, but using a quarter-inch
seam. I sewed around twice because the
pieces were sort of thick.
Just shows you how each Tamarack can look totally different (in the right hands). Fabulous.
ReplyDeleteSuch a great looking jacket! I ordered the fabric , thank you so much for your review on PR.
ReplyDeletenancy
This is just gorgeous! And all the creative work you did to pull it off is just stunning. Bravo!
ReplyDeleteThank you for detailing the steps you took too make this jacket. I've just purchased the pattern and I'll make one for myself. Then I'll see if my sewing student (adult) would like to make one too! I bet she will, and if she or I decide not to use bias binding, your instructions will be SO helpful.
ReplyDeleteThis comment has been removed by the author.
ReplyDeleteThank you so much for your detailing on how you made your jacket - really is a fabulous project and has inspired me no end. Your jacket truly is lovely.
ReplyDelete